|
| |
|
|
 |
Copyright (c) 2006 BKS Farm Imp. Inc. All rights reserved. |
| |
|
 |
 |
| SPARE PARTS |
|
| Supported S Type Cultivator Shank Group |
 |
Partial No: S.TKAK |
| Material: 60SiMn5 |
| Size: 33mm x 13mm cross-section |
| Weight: 3,5 kg./pcs main tine, 2,4 kg./pcs reinforcement shank |
| Hardness: 40~42 HRC |
Other Specifications: Heat treated, ready to mount. Included; Reinforcement shank , clamp, tine, fasteners |
| Interrow Type Shank |
 |
Partial No: AA |
| Material: 60SiMn5 |
| Size: 32mm x 10mm cross-section |
| Weight: 2,6 kg./pcs |
| Hardness: 40~42 HRC |
| Other Specifications: Heat treated, ready to mount. Can be used both of type points, narrow and v-type. |
| |
| Heavy Duty Cultivator Left Shank |
 |
Partial No: TAA |
| Material: 60SiMn5 |
| Size: 30mm x 30mm square cross-section |
| Weight: 13 kg./pcs |
| Hardness: 40~42 HRC |
| Other Specifications: Heat treated, ready to mount. Can be used both of type tines, narrow and v-type. |
|
| |
| Heavy Duty Cultivator Right Shank Group |
 |
Partial No: TKA |
| Material: 60SiMn5 |
| Size: 30mm x 30mm square cross-section |
| Weight: 13 kg./pcs main shank, |
| Hardness: 40~42 HRC |
| Other Specifications: Heat treated, ready to mount. Can be used both of type tines, narrow and v-type. |
|
| |
| Chisel Shank |
 |
Partial No: YP-ÇA |
| Material: Cast Iron Sphero Steel |
| Weight: ~18,5 kg./pcs. (without clamp and screws) |
| Height: 64 cm. (with clamp, from center of profile to ground)) |
| Other Specifications: Shaped with moulding, ready to mount. |
|
| |
| Narrow Type Cultivator Tine |
 |
Partial No: YKU |
| Material: 60SiMn5 |
| Size: 45mm x 6mm cross-section |
| Weight: 300gr./pcs. |
| Hardness: 40~42 HRC |
| Other Specifications: Heat treated and shaped, improved endurance, ready to mount. |
|
| |
| V Type Cultivator Tine |
 |
Partial No: YKKU |
| Material: 60SiMn5 |
Size: 5 mm. sheet iron |
| Weight: |
| Hardness: 40~42 HRC |
| Other Specifications: Heat treated and shaped, improved endurance, ready to mount. |
|
| |
| Narrow Type Heavy Duty Cultivator Tine |
 |
Partial No: TUD |
| Material: 60SiMn5 |
| Size: 65mm x 8mm cross-section |
| Weight: 980gr./pcs. |
| Hardness: 40~42 HRC |
| Other Specifications: Heat treated and shaped, improved endurance, ready to mount. |
|
| |
| Chisel Tine |
 |
Partial No: ÇU |
| Material: 60SiMn5 |
| Size: 60mm x12mm cross-section |
| Weight: 1480gr./pcs. |
| Hardness: 40~42 HRC |
| Other Specifications: Heat treated and shaped, improved endurance, ready to mount. |
|
| |
| Supported S Type Cultivator Shank Mountage Clamp |
 |
Partial No: YKAK |
| Material: St37 Steel |
| Weight: 680gr./pcs. |
| For assembling support and main shank. |
| Other Specifications: Shaped with press, ready to mount. |
|
| |
| S Type Cultivator Shank Mountage Clamp |
 |
Partial No: YKAKT |
| Material: St37 Steel |
| Weight: 730gr./pcs. |
| For use with only main shank |
| Other Specifications: Shaped with press, ready to mount. |
|
| |
| Chisel Shank Mountage Clamp |
 |
Partial No: YP-ÇSK |
| Material: St37 Steel |
| |
| |
| Other Specifications: Ready to mount. |
|
|
| |
| |
|
